Construction Supporting PVC Beam Plastic H20

Product Description

 

Product Description

Product Specification

Product Name: Plastic H beam

Raw Material: Imported Polypropylene Resin

Specification: 9*5cm, 8*4cm, length can be customized, 6m at most

Weight: 1.7kg/m

Product Performance: More than 150 reusable times, light weight, high strength, waterproof and Resistant.

Storage: Open storage

Application: All building support systems

Operation Instruction: When nailing, the distance from H beam edge should be 15-30mm, the strength should be moderate, 40-50mm of the length of nails is better.

STANDARD SIZE	THICKNESS	WEIGHT/PC	QTY/20FT	QTY/40HQ
2440*1220MM	12 MM	21 KGS	560 PCS	1260 PCS
2440*1220MM	15 MM	24 KGS	450 PCS	1026 PCS
2440*1220MM	18 MM	28 KGS	400 PCS	900 PCS
2440*1220MM	20 MM	30 KGS	250 PCS	800 PCS

Cutting and customized size are available.

Product Advantages
1. Durable, the reusable time can reach more than 60 times, long service life.
2. No absorption of moisture, no deformation, no mildew; Long-term immersion stratification in the water,
no bubbles, sheet size stability, especially suitable for underground and damp environment.
3. Demould easily. No need brushing release agent, only tapping, the formwork will fall off. Shorten working
hours and speed up the construction schedule efficiently.
4. Easy to process. Sawing, drilling and nailing are all available. Formworks can be combined vertically 
and horizontally optionally.
5. Light weight, high strength, high hardness, impact resistance, wear resistance.

6. Surface is smooth, bright and clean; concreting and forming effect is good.

7.  Good toughness. It could be used as cambered special-shaped formwork.

8. Acid and alkali resistance, corrosion resistance; Very suitable for the engineeringapplication in 

coastal areas, mine, as well as seawall. It is need not do any preservative treatment both in using and
storing the formwork, which do not pollute the concrete surface.

9. Waste products can be recycled and reprocessed, making full use of waste materials. This property 
can greatly reduce the project cost compared with wooden formwork and bamboo formwork.

10. Environmental protection and energy saving, no pollution. No any poisonous or harmful gas. 

11. Easy to remove. Removing is convenient, quick and safe, and the supporting is also easy to operate,
advantageous to the organization construction, effectively improving the construction schedule.
 

Product Application

Instruction of using Beizhu plastic formwork and H20 beam:

1. Use method is the same as wooden formwork, hollow plastic formwork and batten should be in cross shaped;

2. No need to brush the mold release agent before using formwork;

3. The distance between timbers for 18mm thickness: (A) According to the thickness of the slab concrete, if the
thickness of slab concrete is less than 15cm, the timbers distance should be 350-400mm. If the thickness of slab

concrete is more than 15cm, the distance should be 300-350mm. (B) The distance between timbers of the shear
wall is adjusted by the height and thickness of the wall. For example, the wall is 2800 mm high and 300 mm thick,
timbers distance should be 200-250 mm with 18mm thick plastic formwork. If the shear wall width or the pillar is
thick more than 1m, must add the fixed frame.

4. There shouldn't be gaps between the die shear wall and column combining, there must be timbers in internal
angle (the bottom of the wall) beam to insure the beam frame, wall and formwork connect well. For shear wall,

formwork must be assembled into the whole piece, then hoisting, adjust to be straight. This way can reduce
labor intensity, as well as improve the forming effect.

5. When nailing the formwork and H20 beam, the distance away from formwork edge should be 15-30 mm, the
strength of driving in nail should be moderate; length of nails should be 40-50 mm, not too long or too short.

6. There must be a 15mm seam alowance for the wood in the beam bottom, make the wallboard stand on seam
allowance of wood square, thus can ensure no leakage of slurry and save wallboard material efficiently.

7. Please avoid the peak temperature in one day when matching the mold. Then the effect after releasing mould
is better. Normally, there is no space between formworks, but if the temperature difference is 5-10ºC, then should
reserve 1-2mm gap.

8. Please place the PP formwork as flat as plywood formwork after releasing the mould.

Product Using Feedback

 

Company Profile

                                                                           
                                                                 Beizhu Plastic Formwork Company
 

Beizhu Plastic Formwork Company was founded in 2008, is located in Suqian City,which is one of the
largest manufacturers of construction plastic formwork in China. Beizhu has production area about 12000
square meters, 5 production lines and 100 workers.

 

The construction plastic formwork has been exported to Finland, Canada, Australia, Russia, Ukraine, Kenya
Thailand, Korea and so on. Now Beizhu has 2 agents in Turkey and Thailand.

 

In 2013 year,Beizhu adopted the Certificate of ISO9001:2008 International Quality Management System. 
Beizhu keeps long-term cooperation with all the customers all over the world.